2 hp 110 ~ 120 V AC 1500 watt industrial servo motor & controller Driver Updated

Description

2 HP 1500 Watt Computer Controlled Servo Motor.
New in box.
Sold with a custom built matching control unit
.
Speed is
programmable
for any range between 300 to 3,500 RPM
See images for
measurements
.
Note: the maximum distance between control unit and motor is 22 inches.
Runs on typical 110 to 120 volt AC
household
power
supply's
Includes:
A complete servo motor as seen in images.
A stand alone and
programmable
custom built servo motor driver with overload protection and internal variable speed control.
Toothed L050 pulley not included.
Note I can cut, broach and fit any pulley you chose at additional cost.
1 In stock, tested, boxed and ready to ship!
Whats in the box:
One 1,500 watt (2 HP) servo motor
One customized servo motor
controller with internal speed control
functions
and a thermal overload system..
Motor
programming
+ spindle speeds and Reverse:
The motor speed can be programmed to operate in any range chosen by the user.
Between 300 and 3,500 RPM's.
The full range of speed (RPM's) can also be controlled with just the speed control knob.
Speed control
programming
only requires a few easy steps.
Reverse is simple, just hold the yellow button for a few seconds.
Programming
includes the ability to set bottom and top RPM range separately. In other words you can program the system to run the spindle at any speed or range of speeds you choose (see below).
Slowest speed achievable: Motor 200 RPM.
(Below 300 is not
recommended)
.
Highest speed: 3,500 RPM
.
(Can be programmed to reach 5,000 RPM. This is seriously not recommended. It is also dangerous as in parts could fly across the room causing serious bodily injury even death.) Setting above 3,500 RPM also voids
warranty
.
Soft start is programmable and will be set as soft as possible when you receive this motor. This program is very effective in reducing drive belt wear etc.
Braking strength is also programmable and will be set as low as possible.
Self
diagnostics
with fault code chart.
Safe turn on system where the speed control knob must be in the full counter clockwise (stop) position when turned on. When turned on the self
diagnostic
system checks for faults and will not allow the motor to turn on until the speed control knob is turned all the way to stop first.
Control unit has the ability to stop the motor or what ever it is turning in 2 different locations with external hall effect sensors not included.
Cannot be
programmed
to communicate with any CNC
controller
at this time.
Use at your own risk.
Our liability is limited to the purchase price of this item.
Motor Specifications:
Watt:           1500  (2
HP)
Voltage:      110V
HZ:             60
Torque:      10 N.M.
RPM:
100 to 3,500 RPM
in 100 RPM increments.
Note: Manufacturer recommended 500 to 3,000 RPMs
My personal testing results: This motor runs best between 300 and 3,500 RPMs.
This listing is for what is seen in the primary image.
It will include printed programming instructions.
Recent feedback:
Fantastic setup! Have this on my Taig lathe with 5c head stock and wow!! Thank u!
Can't find this anywhere else. Stupid powerful torque. Great communications. Buy it.
Sh
ipping:
Due to weight it is best to ship USPS
priority
large flat rate box and to USA only.
.50
will
be added to the
order to
cover insurance
Returns:
This item will be is strict
compliance
with the eBay returns
policy's
applied to this item when it was listed.
Buyer has 14 days to file an eBay return request.
Buyer pays return shipping.
All items shipped must be returned in new unused and undamaged condition or no refund will be issued.
Limited 30 to 60 day parts warranty. Labor is buyers responsibility:
See details, what's covered and for how long etc below. Shipping both ways for all parts returned for warranty is the buyers responsibility. Parts returned will be inspected for unique identification mark and or abuse. If found to be abuse or missing the
identity
mark, no warranty exchange part will be provided and buyer will be required to pay shipping to get their parts back. Warranty exchange parts may or may not be new but instead
refurbished
or demos that I have from previous builds. Warranty exchange can take up to 60 days as some parts may not be in stock and require ordering from overseas.
Warranty
starts on the day eBay records the system as paid and not the date the item is actually
received
.
Servo Motor: I will exchange a defective servo motor for up to 60 days. Buyer must return the motor + the control unit + the speed control switch for inspection and testing. Additionally original packaging such as Styrofoam package inserts must be used to return these parts.
Computer control unit (in stock): I will exchange a defective control unit for up to 30 days. Buyer must return the motor + the control unit + the speed control switch for inspection and testing. Additionally original packaging such as Styrofoam package inserts must be used to return these parts.
Ask lots of questions before ordering:
Do not worry about missing this item
and
thus buying it and than changing your mind after the fact.
If you miss it, I will get more soon.